Deleting or updating a marker no longer triggers a full NIO reapply
(reset_packet_filters + re-add), which closed/reopened every sibling
marker's pcap via uBridge. Instead operate on single filters:
- stop_marker: bridge delete_packet_filter + unlink the pcap (works with
the node stopped; filter removal is skipped, the file is still deleted).
- update_marker: bpf/tag/direction → rebuild just that filter (delete + add);
enabled → instant toggle; color/highlight_duration → stored only.
- compute delete_marker_capture / rebuild_marker_filter + per-node routes
(DELETE /markers/{name}, PUT /markers/{name}/rebuild) + MarkerRebuild schema.
IOU overrides _ubridge_delete_marker_filter for iol_bridge; rebuild reuses
the already-overridden add/delete/set, so IOU needs no rebuild override.
The _marker_filter_bridges dict was keyed by marker name alone, so when one
node hosted the same filter name on several links (IUOL-BRIDGE per node with
many bays/units, or a multi-interface router), successive apply calls
overwrote earlier entries. pause_marker_definition then toggled only the last
recorded bridge/location — other copies stayed active and kept emitting.
Key by (name, link_id) so each copy is independent, and iterate all matching
entries in _ubridge_set_marker_filter_state (both generic bridge and IOU
iol_bridge override). Toggle route existence checks also iterate matching
names. Tests updated.
_ubridge_set_marker_filter_state raised "Marker X is not installed on this
node" when the capture node wasn't running — the name->bridge map is only
populated during _ubridge_apply_markers, which runs when the node is up. The
error was noise: the controller's enabled-only short-circuit catches it and
falls back, and the controller-layer enabled is authoritative (honoured when
the node starts and applies the marker). Treat a missing entry as a no-op
instead of raising.
Wire gns3-server to uBridge's real-time marker controls (contract
../ubridge/doc/gns3server-integration.md §3.2), in three layers:
A. enabled reaches uBridge — _markers_for_node no longer drops disabled
markers controller-side; it carries `enabled` in the NIO spec. apply
installs every marker then issues `enable_packet_filter … off` for the
disabled ones (base_node bridge / iou iol_bridge; old-ubridge errors
downgrade to a warning so a toggle can't break link create).
B. instant per-filter toggle — apply records name→bridge so a new
`_ubridge_set_marker_filter_state` can flip a running filter with
`enable_packet_filter on|off` (iou overrides for iol_bridge + bay/unit).
Each marker-capable node type gains PUT /markers/{name}; update_marker
short-circuits to it when only `enabled` changes (no NIO rebuild, no pcap
flush), falling back to reset+reapply if the route is unavailable.
C. global pause/resume — `_ubridge_marker_pause/resume` send `marker pause`
/ `marker resume` direct to the hypervisor (pause stops signal+pcap,
resume instant, sink retained). Six node-type routes add POST
/markers/pause|resume; project.pause_all/resume_all_markers fan out to
each capture node (deduped, best-effort); REST exposes
POST /projects/{id}/markers/pause|resume.
Toggling enabled and pause/resume are now both instant — only marker create
or a bpf change still go through reset+reapply.
Direction field in marker.match events
=======================================
Read ubridge dir=<tx|rx> from MARK signal datagrams and forward it
as a "dir" key in the marker.match notification event. The field is
additive -- older ubridge builds omit it and the parser leaves it null,
so consumers fall back to undirected rendering with no version coupling.
Semantics are relative to the capture node (the signal's node=<id>):
tx = capture node is sending (ingressed device-side NIO), rx = it is
receiving (ingressed link-side NIO).
Per-marker direction filter (opt-in, server-side pipeline)
==========================================================
Add a direction field to MarkerCreate and MarkerDefinitionCreate
schemas ("tx" | "rx" | null). Plumb it through the full pipeline:
Schema -> controller (start_marker/update_marker, marker_entry,
_markers_for_node, update_marker_definition sync)
-> REST/MCP handlers -> compute _ubridge_add_marker_filter +
IOU _ubridge_apply_markers -> bridge add_packet_filter dir <tx|rx>
When set, ubridge only fires the mark handler (signal + pcap) for
packets matching the chosen direction. null (default/legacy) = both
directions -- zero behavioural change for existing markers.
Docs and tests
==============
- docs/features/marker-traffic-insight.md: signal format updated,
new Direction section with NIO mapping, arrow mapping, and additive
compatibility note.
- tests/compute/marker/test_marker_manager.py: 3 new parser tests
(dir tx/rx/absent) plus existing test extended to assert dir=None.
13 files, +123/-22, 72 tests pass (zero breakage)
A uBridge MARK signal carries only node= and filter= (no bridge/link field), so when one node is the capture side for several links that share a marker name (always the case for global-{name} definitions on a multi-interface node) the signals were indistinguishable and the (node, filter) registry collapsed them to a single link.
The mark filter is now stamped with its link id (mark <bpf> ... link <link_id>); uBridge echoes it verbatim (link=<link_id>) and the listener uses the signal's link= as the authoritative link_id of the marker.match event, falling back to the registry only for legacy signals without it. base_node and iou apply paths pass link_id; covered by two new listener tests.
IOU uses iol_bridge (not bridge) with extra bay/unit positional
arguments in add_packet_filter. Add _ubridge_apply_markers override
that mirrors the existing _ubridge_apply_filters pattern, called at
the same three sites: _networking, adapter_add_nio_binding, and
adapter_update_nio_binding.
- Add class-level caches for loader and default RAM/NVRAM values
- When multiple IOU nodes use the same image, only the first one runs
the ld-linux --verify and iou-image -h subprocesses
- Subsequent nodes reuse cached results, saving ~2 subprocess calls per node
- Cache is populated only on successful subprocess execution to avoid
overwriting explicitly set ram/nvram values with stale cached defaults
When a hostname validation fails, the error message now includes
the allowed character set to help users provide valid names.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
An application ID is used by IOU to generate its interface Mac addresses. They must be unique across all opened projects sharing the same computes to avoid Mac address collisions.
